Chapter XVI

Subchapter A

Subpart 1

23 CAR § 460-101 Declaration of public policy {#sec-23-car-460-101 omnilex-key=us-ar-regs-official--title-23-part-460--23 CAR § 460-101}

23 CAR § 460-101. Declaration of public policy.

(a)(1) In light of events that have occurred subsequent to the issuance of the 1971 Rules and Regulations Governing Promotional Practices of Electric and Gas Public Utilities (“1971 rules”), competition among electric and gas utilities must now exist in an era of energy conservation and integrated resource planning.

(2) As these utilities seek to maximize the use of existing generating plants and reserves, to use wisely the natural resources that provide their fuel, and, thus, to encourage their customers to conserve energy where possible, the Arkansas Public Service Commission has determined that promotional practices must:

(A) Benefit ratepayers in the aggregate; or

(B) Not be engaged in at all.

(b)(1) The promotion of goods or services offered the public is an inherent and important part of the economy of the state and nation.

(2) However, any electric and gas utilities desiring to engage in promotional practices have the burden of proving that the proposed practices:

(A) Are not unduly discriminatory or anticompetitive; and

(B) Are in the public interest because they serve the purposes of energy conservation pursuant to the authority granted the Arkansas Public Service Commission in the Energy Conservation Endorsement Act of 1977, Arkansas Code § 23-3-401 et seq.

(3) The laws of this state require the rates of a public utility to be just and reasonable and in conformity with the rules and orders of the Arkansas Public Service Commission.

(4) The laws prohibit a public utility from directly or indirectly demanding or receiving from anyone a greater or lesser rate for service than that specified in its tariff.

(5) The laws prohibit, with respect to rates and services:

(A) The granting of unreasonable preferences or advantages to anyone; or

(B) Subjecting anyone to unreasonable prejudice or disadvantage.

(6) The laws grant the Arkansas Public Service Commission the authority to encourage energy conservation.

(7) Accordingly, the Arkansas Public Service Commission declares that the adoption and enforcement of this part is in the public interest because it seeks to advance the welfare of all consumers by prohibiting all promotional practices unless approval by the Arkansas Public Service Commission has been granted after investigation and hearing.

History

Codification Notes: This section was promulgated as Section 1 of the Promotional Practices of Electric and Gas Public Utilities prior to codification in the Code of Arkansas Rules. Authority: Arkansas Code § 23-2-305

23 CAR § 460-102 Definitions {#sec-23-car-460-102 omnilex-key=us-ar-regs-official--title-23-part-460--23 CAR § 460-102}

23 CAR § 460-102. Definitions.

The following words, when used in this part, shall have the following meanings unless otherwise clearly apparent from the context:

(1) “Appliance or equipment” means any:

(A) Device, including a fixture, that consumes electric or gas energy; and

(B) Ancillary device required for its operation, including computer hardware and software;

(2) “Consideration” means any:

(A) Cash;

(B) Donation;

(D) Allowance;

(E) Rebate;

(F) Bonus;

(G) Merchandise, new or used;

(H) Property, tangible or intangible;

(I) Labor;

(J) Service;

(K) Conveyance;

(L) Commitment;

(M) Right; or

(N) Other thing of value;

(3) “Financing” includes:

(A) Acquisition of equity or debt interests;

(B) Loans;

(D) Advances;

(E) Sale and repurchase agreements;

(F) Sale and leaseback agreements;

(G) Sales on open account;

(H) Conditional or installment sales contracts; or

(I) Other investments or extensions of credit;

(4) “Person” includes any:

(A) Individual;

(B) Group;

(D) Partnership;

(E) Corporation;

(F) Cooperative;

(G) Association; or

(H) Other organization;

(5) “Promotional practices” means any consideration offered by a public utility to any person for the purpose, express or implied, of inducing such person to select or use the service or additional service or to conserve the use of service of such or any utility, or to select or install any appliance or equipment designed to use such or any utility service, provided that the words “promotional practices”:

(A) Shall include but not be limited to the following activities of a public utility:

(i)(a) Merchandising of appliances or equipment unless such activity is operated as a nonutility business as provided at subdivision (5)(B)(i) of this section.

(b) Merchandising activities that are not completely segregated from public utility activities and property shall be deemed promotional practices;

(ii) The financing of the acquisition of any appliance or equipment, unless such activity is operated as a nonutility business as provided at subdivision (5)(B)(i), at a rate of interest or on terms significantly more favorable than those generally applicable to sales by nonutility dealers in such appliances or equipment;

(iii) The financing of land or the construction of any building when same is not owned or otherwise possessed by the utility;

(iv) The furnishing of consideration to any person for work done or to be done on property not owned or otherwise possessed by the utility;

(v) The acquisition from any person of any tangible or intangible property or service for a consideration in excess of the value thereof, or the furnishing to any person of any tangible or intangible property or service for a consideration of less than the value thereof;

(vi) The furnishing of consideration to any person for the sale, installation, or use of appliances or equipment;

(vii) The guaranteeing of the maximum cost of electric or gas utility service;

(viii) The furnishing of distribution and service facilities to any area or customer under terms and conditions different from those applicable to any other area or customer receiving the particular class of service involved;

(ix) The furnishing of consideration by a utility to any person who, on behalf of the utility, performs any promotional practice as otherwise defined in this section; and

(x) Special rate contracts between a utility and an individual customer; and

(B) Shall not include the following activities of a public utility:

(i) Merchandising or financing of appliances or equipment if such activity is operated as a nonutility business, i.e., the activities must be completely segregated from public utility activities and must meet the following requirements:

(a) Accounting for the activities is completely separate;

(b) Collection for financing is not made on the customer’s utility bill;

(d) Public utility property of activities, such as billing inserts, are not used to advertise the nonpublic utility activities;

(ii) Inspections, repairs, and service:

(a) For the purpose of providing or restoring utility service; or

(b) To prevent hazardous conditions or service interruptions to a customer;

(iii) Providing appliances or equipment incidental to exhibitions, demonstrations, tests, or experiments of a reasonable duration;

(iv) Providing appliances, equipment, or instructional services to an educational institution for the purpose of instructing students in the use or repair of such appliances or equipment;

(v) Technical, informational, or educational assistance offered to persons on the use of energy furnished by a public utility or on the use or maintenance of appliances or equipment; and

(vi) Rates reflecting variations in the utility’s actual cost of providing service, including but not limited to time-of-use, summer/winter differential, and interruptible or curtailable rates;

(6) “Public utility” or “utility” means any person engaged in the production, storage, distribution, sale, delivery, or furnishing of electricity or gas subject to the jurisdiction of the Arkansas Public Service Commission; and

(7) “Tests” means the Participant Test, the Ratepayer Impact Measure Test, the Total Resource Cost Test, and the Utility Cost Test as summarized in the appendix to this part.

History

Codification Notes: This section was promulgated as Section 2 of the Promotional Practices of Electric and Gas Public Utilities prior to codification in the Code of Arkansas Rules. Authority: Arkansas Code § 23-2-305

23 CAR § 460-103 Prohibition of promotional practices {#sec-23-car-460-103 omnilex-key=us-ar-regs-official--title-23-part-460--23 CAR § 460-103}

23 CAR § 460-103. Prohibition of promotional practices.

(a) A public utility shall not, without first obtaining the approval of the Arkansas Public Service Commission, engage in any promotional practices.

(b) Any public utility engaging in promotional practices after the effective date of this part without approval of such practices by the Arkansas Public Service Commission will be subject to penalty under Arkansas Code § 23-1-103, except as allowed under 23 CAR § 460-109.

History

Codification Notes: This section was promulgated as Section 3 of the Promotional Practices of Electric and Gas Public Utilities prior to codification in the Code of Arkansas Rules. Authorities: Arkansas Code § 23-1-103; Arkansas Code § 23-2-305

23 CAR § 460-104 Standards governing promotional practices {#sec-23-car-460-104 omnilex-key=us-ar-regs-official--title-23-part-460--23 CAR § 460-104}

23 CAR § 460-104. Standards governing promotional practices.

The following standards shall govern the utility’s promotional practices:

(1)(A) A promotional practice must be in the public interest.

(B) In determining whether a practice is in the public interest, the Arkansas Public Service Commission shall consider the following:

(i) Cost efficiency of the proposed promotional practice using the:

(a) Total Resource Cost Test;

(b) Participant Test; and

(ii) Ratepayer impact of the proposed promotional practices using the Ratepayer Impact Measure Test;

(2)(A) No public utility shall directly or indirectly in any manner or by any device whatsoever offer to any person any form of promotional practice except such as is uniformly and contemporaneously extended to all persons in a reasonably defined class.

(B) No public utility shall, in the offering of a promotional practice:

(i) Give any undue preference or advantage to any person; or

(ii) Subject any person to any undue prejudice or disadvantage.

(C) No public utility shall establish or maintain any unreasonable difference in the offering of promotional practices either as between localities or as between classes to whom promotional practices are offered.

(D) No public utility shall classify the persons to whom its promotional practices are offered except to the extent permitted by the laws of this state; and

(3) All advertising associated with a promotional practice shall be truthful and not misleading or deceptive.

History

Codification Notes: This section was promulgated as Section 4 of the Promotional Practices of Electric and Gas Public Utilities prior to codification in the Code of Arkansas Rules. Authority: Arkansas Code § 23-2-305

23 CAR § 460-105 Filing of proposed promotional practices {#sec-23-car-460-105 omnilex-key=us-ar-regs-official--title-23-part-460--23 CAR § 460-105}

23 CAR § 460-105. Filing of proposed promotional practices.

(a)(1) After the effective date of this part, any utility wishing to engage in any promotional practice must file an application for approval by the Arkansas Public Service Commission.

(2) All applications for approval of a promotional practice shall be assigned a “P” docket designation by the secretary of the Arkansas Public Service Commission.

(3) Any application filed pursuant to this part shall also be governed by the Arkansas Public Service Commission’s Rules of Practice and Procedure, 23 CAR pt. 462.

(b)(1) Upon application of the utility, the Arkansas Public Service Commission shall:

(A) Conduct an investigation of the proposed promotional practice; and

(B) Make a determination whether it is in the public interest.

(2) The application shall include a schedule for each proposed promotional practice setting forth:

(A) The name, number, or letter designation of each promotional practice;

(B) The class of persons to which the promotional practice is being offered;

(D) A description of the promotional practice that shall include a statement of the terms and conditions governing the same;

(E) A description of the advertising or publicity employed with respect to the utility’s promotional practice, and the proposed methodology for accounting for these costs;

(F) If the promotional practice is offered, in whole or in part, by some other person, the identity of such person and the nature of such person’s participation;

(G) The objectives of the promotional practice;

(H) The expected beginning and ending dates of the promotional practice;

(I) An estimate of the number of persons who are potential participants in the promotional practice;

(J) The proposed accounting for the costs and benefits of the promotional practice;

(K) Sufficiently detailed calculations, sensitivity analysis, and supporting testimony of the effect of the promotional practice using each of the applicable tests, as determined by the California Standard Practice Manual, Economic Analysis of Demand-Side Management Programs and Projects, and an explanation of why any particular test is not applicable to the proposed promotional practice;

(L) A description of the relevant competing energy resources in the service area where the promotional practice will be offered, and the extent to which they are considered in the calculations in the tests; and

(M) Any other information relevant to a complete understanding of the promotional practice.

History

Codification Notes: This section was promulgated as Section 5 of the Promotional Practices of Electric and Gas Public Utilities prior to codification in the Code of Arkansas Rules. Authority: Arkansas Code § 23-2-305

23 CAR § 460-106 Approval by the Arkansas Public Service Commission {#sec-23-car-460-106 omnilex-key=us-ar-regs-official--title-23-part-460--23 CAR § 460-106}

23 CAR § 460-106. Approval by the Arkansas Public Service Commission.

(a) A proposed promotional practice filed pursuant to this part may be implemented by the applicant thirty (30) days after the date of filing unless the Arkansas Public Service Commission, upon its own motion or the motion of any party, issues an order suspending the implementation of the proposed promotional practice pending further investigation.

(b) However, the suspension shall not be for a longer period than one hundred fifty (150) days beyond the time when the proposed promotional practice would otherwise go into effect.

(c) Any order initially suspending a proposed promotional practice shall set an appropriate procedural schedule and a specific date for the commencement of a public hearing inquiring into the proposed promotional practice unless waived by the applicant.

History

Codification Notes: This section was promulgated as Section 6 of the Promotional Practices of Electric and Gas Public Utilities prior to codification in the Code of Arkansas Rules. Authority: Arkansas Code § 23-2-305

23 CAR § 460-107 Notices {#sec-23-car-460-107 omnilex-key=us-ar-regs-official--title-23-part-460--23 CAR § 460-107}

23 CAR § 460-107. Notices.

(a)(1) The secretary of the Arkansas Public Service Commission shall establish a promotional practices reporting docket that shall serve as a repository for all:

(A) Notices filed pursuant to this section; and

(B) Biennial reports filed pursuant to 23 CAR § 460-108.

(2) Said promotional practices reporting docket shall be designated by the secretary of the Arkansas Public Service Commission as a “PR” docket.

(b) After a promotional practice has been approved by the Arkansas Public Service Commission, the utility engaging in the practice shall file a notice in the promotional practices reporting docket, referencing the docket in which the promotional practice was approved, whenever any of the following events occur:

(1) Commencement of the practice;

(2) Material variance in the number of participants or the cost or benefits of the practice that alters the results of the tests presented in the utility’s application; and

(3) Cancellation of the practice.

History

Codification Notes: This section was promulgated as Section 7 of the Promotional Practices of Electric and Gas Public Utilities prior to codification in the Code of Arkansas Rules. Authority: Arkansas Code § 23-2-305

23 CAR § 460-108 Biennial report {#sec-23-car-460-108 omnilex-key=us-ar-regs-official--title-23-part-460--23 CAR § 460-108}

23 CAR § 460-108. Biennial report.

(a) After approval by the Arkansas Public Service Commission of any public utility’s promotional practices, each public utility engaging in approved promotional practices shall file with the Arkansas Public Service Commission every two (2) years beginning June 30, 1994, in the promotional practices reporting docket, a report of the promotional practices offered by such public utility during the period covered by such report.

(b) The report shall include a certificate signed by an officer of the utility that contains the following information for its approved promotional practices:

(1) The promotional practices currently engaged in, referencing the docket in which each specific promotional practice was approved;

(2) The number of customers participating in each promotional practice by class;

(3) Any promotional practices terminated since the last report and an explanation of why they were terminated;

(4) Total expenditures incurred by the utility for each promotional practice, by category, e.g., general and administrative, sales, plant, etc.;

(5) Analyses of each promotional practice incorporating the most current data in the relevant tests;

(6) A description of the advertising or publicity employed with respect to the utility’s promotional practices;

(7) An attestation of compliance with this part; and

(8) An attestation that all of the utility’s promotional practices are on file with the Arkansas Public Service Commission.

History

Codification Notes: This section was promulgated as Section 8 of the Promotional Practices of Electric and Gas Public Utilities prior to codification in the Code of Arkansas Rules. Authority: Arkansas Code § 23-2-305

23 CAR § 460-109 Transition period {#sec-23-car-460-109 omnilex-key=us-ar-regs-official--title-23-part-460--23 CAR § 460-109}

23 CAR § 460-109. Transition period.

(a)(1) Pursuant to 23 CAR § 460-103, all promotional practices of electric and gas utilities are prohibited unless approval has been granted by the Arkansas Public Service Commission.

(2) In order to provide an orderly transition from the 1971 Rules and Regulations Governing Promotional Practices of Electric and Gas Public Utilities to this part, the Arkansas Public Service Commission hereby establishes a transition period for the filing and approval of:

(A) Promotional practices currently engaged in by a utility that are not defined as a promotional practice in the 1971 rules; and

(B)(i) Tariffs and other programs approved by the Arkansas Public Service Commission before May 8, 1992, that meet the definition of promotional practices embodied herein.

(ii) Such promotional practices must be filed in accordance with 23 CAR § 460-105 at least one hundred eighty (180) days before the end of the transition period.

(iii) The transition period will expire January 25, 1995.

(iv) By the end of the transition period, any utility wishing to continue such practices must have secured Arkansas Public Service Commission approval for such practices pursuant to this part or cease such practices.

(b) Notwithstanding any provision of this part, a public utility may perform lawful commitments concerning promotional practices entered into prior to the effective date of this part, or entered into pursuant to a tariff that was approved prior to the effective date of this part, if a detailed description of such commitments is filed with the Arkansas Public Service Commission by January 25, 1995, describing the nature of each commitment and the reasons for which the commitment has been incurred, provided that:

(1) Such a commitment may be hereafter terminated by the Arkansas Public Service Commission:

(A) After notice;

(B) After opportunity for hearing; and

(2)(A) Such a commitment is not prohibited by the 1971 rules.

(B) Any determination by the Arkansas Public Service Commission allowing these lawful commitments to be honored by a public utility shall not constitute approval of the promotional practice.

(C) Arkansas Public Service Commission approval of any such promotional practice must be sought pursuant to the provisions of this part.

History

Codification Notes: This section was promulgated as Section 9 of the Promotional Practices of Electric and Gas Public Utilities prior to codification in the Code of Arkansas Rules. Authority: Arkansas Code § 23-2-305

23 CAR pt. 460, Appendix A California Standard Practice Manual - Economic Analysis of Demand-Side Programs and Projects {#sec-23-car-pt.-460-appendix-a omnilex-key=us-ar-regs-official--title-23-part-460--23 CAR pt. 460, Appendix A}

CALIFORNIA STANDARD PRACTICE MANUAL

ECONOMIC ANALYSIS OF DEMAND-SIDE PROGRAMS AND PROJECTS

OCTOBER 2001

1 Table of Contents Page

Chapter 1..............................................................................................................................1 Basic Methodology...............................................................................................................1 Background.......................................................................................................................1 Demand-Side Management Categories and Program Definitions.......................................2 Basic Methods..................................................................................................................4 Balancing the Tests...........................................................................................................6 Limitations: Externality Values and Policy Rules..............................................................6 Externality Values.............................................................................................................7 Policy Rules......................................................................................................................7 Chapter 2..............................................................................................................................8 Participant Test.....................................................................................................................8 Definition..........................................................................................................................8 Benefits and Costs.............................................................................................................8 How the Results Can be Expressed....................................................................................9 Strengths of the Participant Test........................................................................................9 Weaknesses of the Participant Test..................................................................................10 Formulae.........................................................................................................................10 Chapter 3............................................................................................................................13 The Ratepayer Impact Measure Test...................................................................................13 Definition........................................................................................................................13 Benefits and Costs...........................................................................................................13 How the Results can be Expressed..................................................................................13 Strengths of the Ratepayer Impact Measure (RIM) Test..................................................14 Weaknesses of the Ratepayer Impact Measure (RIM) Test..............................................15 Chapter 4............................................................................................................................18 Total Resource Cost Test....................................................................................................18 Definition........................................................................................................................18 How the Results Can be Expressed..................................................................................19 Strengths of the Total Resource Cost Test.......................................................................21 Weakness of the Total Resource Cost Test......................................................................21 Formulas.........................................................................................................................21 Chapter 5............................................................................................................................23 Program Administrator Cost Test........................................................................................23 Definition........................................................................................................................23 Benefits and Costs...........................................................................................................23 How the Results Can be Expressed..................................................................................23 Strengths of the Program Administrator Cost Test...........................................................24 Weaknesses of the Program Administrator Cost Test.......................................................24 Formulas.........................................................................................................................24 Appendix A........................................................................................................................26 Inputs to Equations and Documentation..............................................................................26 Appendix B.........................................................................................................................28

2 Summary of Equations and Glossary of Symbols................................................................28 Basic Equations...............................................................................................................28 Participant Test...........................................................................................................28 Ratepayer Impact Measure Test...................................................................................28 Total Resource Cost Test.............................................................................................28 Program Administrator Cost Test................................................................................28 Benefits and Costs...........................................................................................................29 Participant Test...........................................................................................................29 Ratepayer Impact Measure Test...................................................................................29 Total Resource Cost Test.............................................................................................29 Program Administrator Cost Test................................................................................30 Glossary of Symbols.......................................................................................................30 Appendix C.........................................................................................................................33 Derivation of Rim Lifecycle Revenue Impact Formula........................................................33 Rate Impact Measure.......................................................................................................33

1 Chapter 1 Basic Methodology Background Since the 1970s, conservation and load management programs have been promoted by the California Public Utilities Commission (CPUC) and the California Energy Commission (CEC) as alternatives to power plant construction and gas supply options. Conservation and load management (C&LM) programs have been implemented in California by the major utilities through the use of ratepayer money and by the CEC pursuant to the CEC legislative mandate to establish energy efficiency standards for new buildings and appliances.

While cost-effectiveness procedures for the CEC standards are outlined in the Public Resources Code, no such official guidelines existed for utility-sponsored programs. With the publication of the Standard Practice for Cost-Benefit Analysis of Conservation and Load Management Programs in February 1983, this void was substantially filled. With the informal "adoption" one year later of an appendix that identified cost-effectiveness procedures for an "All Ratepayers" test, C&LM program cost effectiveness consisted of the application of a series of tests representing a variety of perspectives-participants, non- participants, all ratepayers, society, and the utility.

The Standard Practice Manual was revised again in 1987-88. The primary changes (relative to the 1983 version), were: (1) the renaming of the “Non-Participant Test” to the “Ratepayer Impact Test“; (2) renaming the All-Ratepayer Test” to the “Total Resource Cost Test.”; (3) treating the “Societal Test” as a variant of the “Total Resource Cost Test;” and, (4) an expanded explanation of “demand-side” activities that should be subjected to standard procedures of benefit-cost analysis.

Further changes to the manual captured in this (2001) version were prompted by the cumulative effects of changes in the electric and natural gas industries and a variety of changes in California statute related to these changes. As part of the major electric industry restructuring legislation of 1996 (AB1890), for example, a public goods charge was established that ensured minimum funding levels for “cost effective conservation and energy efficiency” for the 1998-2002 period, and then (in 2000) extended through the year 2011. Additional legislation in 2000 (AB1002) established a natural gas surcharge for similar purposes. Later in that year, the Energy Security and Reliability Act of 2000 (AB970) directed the California Public Utilities Commission to establish, by the Spring of 2001, a distribution charge to provide revenues for a self generation program and a directive to consider changes to cost-effectiveness methods to better account for reliability concerns.

In the Spring of 2001, a new state agency — the Consumer Power and Conservation Financing Authority — was created. This agency is expected to provide additional revenues in the form of state revenue bonds that could supplement the amount and type of public financial resources to finance energy efficiency and self generation activities.

The modifications to the Standard Practice Manual reflect these more recent developments in several ways. First, the “Utility Cost Test” is renamed the “Program Administrator Test” to include the assessment of programs managed by other agencies. Second, a definition of self generation as a type of “demand-side” activity is included. Third, the description of the various potential elements of “externalities” in the Societal version of the TRC test is expanded. Finally the limitations section outlines the scope of this manual and elaborates upon the processes traditionally instituted by implementing agencies to adopt values for these externalities and to adopt the the policy rules that accompany this manual.

Demand-Side Management Categories and Program Definitions One important aspect of establishing standardized procedures for cost-effectiveness evaluations is the development and use of consistent definitions of categories, programs, and program elements.

This manual employs the use of general program categories that distinguish between different types of demand-side management programs, conservation, load management, fuel substitution, load building and self-generation. Conservation programs reduce electricity and/or natural gas consumption during all or significant portions of the year. ‘Conservation’ in this context includes all ‘energy efficiency improvements’. An energy efficiency improvement can be defined as reduced energy use for a comparable level of service, resulting from the installation of an energy efficiency measure or the adoption of an energy efficiency practice. Level of service may be expressed in such ways as the volume of a refrigerator, temperature levels, production output of a manufacturing facility, or lighting level per square foot. Load management programs may either reduce electricity peak demand or shift demand from on peak to non-peak periods.

Fuel substitution and load building programs share the common feature of increasing annual consumption of either electricity or natural gas relative to what would have happened in the absence of the program. This effect is accomplished in significantly different ways, by inducing the choice of one fuel over another (fuel substitution), or by increasing sales of electricity, gas, or electricity and gas (load building). Self generation refers to distributed generation (DG) installed on the customer’s side of the electric utility meter, which serves some or all of the customer's electric load, that otherwise would have been provided by the central electric grid.

In some cases, self generation products are applied in a combined heat and power manner, in which case the heat produced by the self generation product is used on site to provide some or all of the customer’s thermal needs. Self generation technologies include, but are not limited to, photovoltaics, wind turbines, fuel cells, microturbines, small gas-fired turbines, and gas-fired internal combustion engines.

Fuel substitution and load building programs were relatively new to demand-side management in California in the late 1980s, born out of the convergence of several factors

3 that translated into average rates that substantially exceeded marginal costs. Proposals by utilities to implement programs that increase sales had prompted the need for additional procedures for estimating program cost effectiveness. These procedures maybe applicable in a new context. AB 970 amended the Public Utilities Code and provided the motivation to develop a cost-effectiveness method that can be used on a common basis to evaluate all programs that will remove electric load from the centralized grid, including energy efficiency, load control/demand-responsiveness programs and self-generation. Hence, self- generation was also added to the list of demand side management programs for cost- effectiveness evaluation. In some cases, self-generation programs installed with incremental load are also included since the definition of self-generation is not necessarily confined to projects that reduce electric load on the grid. For example, suppose an industrial customer installs a new facility with a peak consumption of 1.5 MW, with an integrated on-site 1.0 MW gas fired DG unit. The combined impact of the new facility is load building since the new facility can draw up to 0.5 MW from the grid, even when the DG unit is running. The proper characterization of each type of demand-side management program is essential to ensure the proper treatment of inputs and the appropriate interpretation of cost-effectiveness results.

Categorizing programs is important because in many cases the same specific device can be and should be evaluated in more than one category. For example, the promotion of an electric heat pump can and should be treated as part of a conservation program if the device is installed in lieu of a less efficient electric resistance heater. If the incentive induces the installation of an electric heat pump instead of gas space heating, however, the program needs to be considered and evaluated as a fuel substitution program. Similarly, natural gas- fired self-generation, as well as self-generation units using other non-renewable fossil fuels, must be treated as fuel-substitution. In common with other types of fuel-substitution, any costs of gas transmission and distribution, and environmental externalities, must be accounted for. In addition, cost-effectiveness analyses of self-generation should account for utility interconnection costs. Similarly, a thermal energy storage device should be treated as a load management program when the predominant effect is to shift load. If the acceptance of a utility incentive by the customer to, install the energy storage device is a decisive aspect of the customer's decision to remain an electric utility customer (i.e., to reject or defer the option of installing a gas-fired cogeneration system), then the predominant effect of the thermal energy storage device has been to substitute electricity service for the natural gas service that would have occurred in the absence of the program.

In addition to Fuel Substitution and Load Building Programs, recent utility program proposals have included reference to "load retention," "sales retention," "market retention," or "customer retention" programs. In most cases, the effect of such programs is identical to either a Fuel Substitution or a Load Building program — sales of one fuel are increased relative to sales without the program. A case may be made, however, for defining a separate category of program called "load retention." One unambiguous example of a load retention program is the situation where a program keeps a customer from relocating to another utility service area. However, computationally the equations and guidelines included in this manual to accommodate Fuel Substitution and Load Building programs can also handle this special situation as well.

Basic Methods This manual identifies the cost and benefit components and cost-effectiveness calculation procedures from four major perspectives: Participant, Ratepayer Impact Measure (RIM), Program Administrator Cost (PAC), and Total Resource Cost (TRC). A fifth perspective, the Societal, is treated as a variation on the Total Resource Cost test. The results of each perspective can be expressed in a variety of ways, but in all cases it is necessary to calculate the net present value of program impacts over the lifecycle of those impacts.

Table I summarizes the cost-effectiveness tests addressed in this manual. For each of the perspectives, the table shows the appropriate means of expressing test results. The primary unit of measurement refers to the way of expressing test results that are considered by the staffs of the two Commissions as the most useful for summarizing and comparing demand- side management (DSM) program cost-effectiveness. Secondary indicators of cost- effectiveness represent supplemental means of expressing test results that are likely to be of particular value for certain types of proceedings, reports, or programs.

This manual does not specify how the cost-effectiveness test results are to be displayed or the level at which cost-effectiveness is to be calculated (e.g., groups of programs, individual programs, and program elements for all or some programs). It is reasonable to expect different levels and types of results for different regulatory proceedings or for different phases of the process used to establish proposed program-funding levels. For example, for summary tables in general rate case proceedings at the CPUC, the most appropriate tests may be the RIM lifecycle revenue impact, Total Resource Cost, and Program Administrator Cost test results for programs or groups of programs. The analysis and review of program proposals for the same proceeding may include Participant test results and various additional indicators of cost-effectiveness from all tests for each individual program element. In the case of cost-effectiveness evaluations conducted in the context of integrated long-term resource planning activities, such detailed examination of multiple indications of costs and benefits may be impractical.

Table I Cost-Effectiveness Tests

Participant Primary Secondary Net present value (all participants) Discounted payback (years) Benefit-cost ratio Net present value (average participant) Ratepayer Impact Measure Lifecycle revenue impact per Unit of energy (kWh or therm) or demand customer (kW)

Net present value

Lifecycle revenue impact per unit Annual revenue impact (by year, per kWh, kW, therm, or customer) First-year revenue impact (per kWh, kW, therm, or customer) Benefit-cost ratio Total Resource Cost Net present value (NPV)

Benefit-cost ratio (BCR) Levelized cost (cents or dollars per unit of energy or demand) Societal (NPV, BCR) Program Administrator Cost Net present value Benefit-cost ratio Levelized cost (cents or dollars per unit of energy or demand)

Rather than identify the precise requirements for reporting cost-effectiveness results for all types of proceedings or reports, the approach taken in this manual is to (a) specify the components of benefits and costs for each of the major tests, (b) identify the equations to be used to express the results in acceptable ways; and (c) indicate the relative value of the different units of measurement by designating primary and secondary test results for each test.

It should be noted that for some types of demand-side management programs, meaningful cost-effectiveness analyses cannot be performed using the tests in this manual. The following guidelines are offered to clarify the appropriated "match" of different types of programs and tests:

For generalized information programs (e.g., when customers are provided generic information on means of reducing utility bills without the benefit of on-site evaluations or customer billing data), cost-effectiveness tests are not expected because of the extreme difficulty in establishing meaningful estimates of load impacts.

6 2. For any program where more than one fuel is affected, the preferred unit of measurement for the RIM test is the lifecycle revenue impacts per customer, with gas and electric components reported separately for each fuel type and for combined fuels.

For load building programs, only the RIM tests are expected to be applied. The Total Resource Cost and Program Administrator Cost tests are intended to identify cost- effectiveness relative to other resource options. It is inappropriate to consider increased load as an alternative to other supply options.
Levelized costs may be appropriate as a supplementary indicator of cost per unit for electric conservation and load management programs relative to generation options and gas conservation programs relative to gas supply options, but the levelized cost test is not applicable to fuel substitution programs (since they combine gas and electric effects) or load building programs (which increase sales).

The delineation of the various means of expressing test results in Table 1 is not meant to discourage the continued development of additional variations for expressing cost- effectiveness. Of particular interest is the development of indicators of program cost effectiveness that can be used to assess the appropriateness of program scope (i.e. level of funding) for General Rate Case proceedings. Additional tests, if constructed from the net present worth in conformance with the equations designated in this manual, could prove useful as a means of developing methodologies that will address issues such as the optimal timing and scope of demand-side management programs in the context of overall resource planning.

Balancing the Tests The tests set forth in this manual are not intended to be used individually or in isolation. The results of tests that measure efficiency, such as the Total Resource Cost Test, the Societal Test, and the Program Administrator Cost Test, must be compared not only to each other but also to the Ratepayer Impact Measure Test. This multi-perspective approach will require program administrators and state agencies to consider tradeoffs between the various tests. Issues related to the precise weighting of each test relative to other tests and to developing formulas for the definitive balancing of perspectives are outside the scope of this manual. The manual, however, does provide a brief description of the strengths and weaknesses of each test (Chapters 2, 3, 4, and 5) to assist users in qualitatively weighing test results.

Limitations: Externality Values and Policy Rules The list of externalities identified in Chapter 4, page 27, in the discussion on the Societal version of the Total Resource Cost test is broad, illustrative and by no means exhaustive. Traditionally, implementing agencies have independently determined the details such as the components of the externalities, the externality values and the policy rules which specify the contexts in which the externalities and the tests are used.

7 Externality Values The values for the externalities have not been provided in the manual. There are separate studies and methodologies to arrive at these values. There are also separate processes instituted by implementing agencies before such values can be adopted formally.

Policy Rules The appropriate choice of inputs and input components vary by program area and project. For instance, low income programs are evaluated using a broader set of non-energy benefits that have not been provided in detail in this manual. Implementing agencies traditionally have had the discretion to use or to not use these inputs and/or benefits on a project- or program-specific basis. The policy rules that specify the contexts in which it is appropriate to use the externalities, their components, and tests mentioned in this manual are an integral part of any cost-effectiveness evaluation. These policy rules are not a part of this manual.

To summarize, the manual provides the methodology and the cost-benefit calculations only. The implementing agencies (such as the California Public Utilities Commission and the California Energy Commission) have traditionally utilized open public processes to incorporate the diverse views of stakeholders before adopting externality values and policy rules which are an integral part of the cost-effectiveness evaluation.

8 Chapter 2 Participant Test Definition The Participants Test is the measure of the quantifiable benefits and costs to the customer due to participation in a program. Since many customers do not base their decision to participate in a program entirely on quantifiable variables, this test cannot be a complete measure of the benefits and costs of a program to a customer.

Benefits and Costs The benefits of participation in a demand-side program include the reduction in the customer's utility bill(s), any incentive paid by the utility or other third parties, and any federal, state, or local tax credit received. The reductions to the utility bill(s) should be calculated using the actual retail rates that would have been charged for the energy service provided (electric demand or energy or gas). Savings estimates should be based on gross savings, as opposed to net energy savings 1 .

In the case of fuel substitution programs, benefits to the participant also include the avoided capital and operating costs of the equipment/appliance not chosen. For load building programs, participant benefits include an increase in productivity and/or service, which is presumably equal to or greater than the productivity/ service without participating. The inclusion of these benefits is not required for this test, but if they are included then the societal test should also be performed.

The costs to a customer of program participation are all out-of-pocket expenses incurred as a result of participating in a program, plus any increases in the customer's utility bill(s). The out-of-pocket expenses include the cost of any equipment or materials purchased, including sales tax and installation; any ongoing operation and maintenance costs; any removal costs (less salvage value); and the value of the customer's time in arranging for the installation of the measure, if significant.

1 Gross energy savings are considered to be the savings in energy and demand seen by the participant at the meter. These are the appropriate program impacts to calculate bill reductions for the Participant Test. Net savings are assumed to be the savings that are attributable to the program. That is, net savings are gross savings minus those changes in energy use and demand that would have happened even in the absence of the program. For fuel substitution and load building programs, gross-to-net considerations account for the impacts that would have occurred in the absence of the program.

9 How the Results can be Expressed The results of this test can be expressed in four ways: through a net present value per average participant, a net present value for the total program, a benefit-cost ratio or discounted payback. The primary means of expressing test results is net present value for the total program; discounted payback, benefit-cost ratio, and per participant net present value are secondary tests.

The discounted payback is the number of years it takes until the cumulative discounted benefits equal or exceed the cumulative discounted costs. The shorter the discounted payback, the more attractive or beneficial the program is to the participants. Although "payback period" is often defined as undiscounted in the textbooks, a discounted payback period is used here to approximate more closely the consumer's perception of future benefits and costs. 2

Net present value (NPVp) gives the net dollar benefit of the program to an average participant or to all participants discounted over some specified time period. A net present value above zero indicates that the program is beneficial to the participants under this test.

The benefit-cost ratio (BCRp) is the ratio of the total benefits of a program to the total costs discounted over some specified time period. The benefit-cost ratio gives a measure of a rough rate of return for the program to the participants and is also an indication of risk. A benefit-cost ratio above one indicates a beneficial program.

Strengths of the Participant Test The Participants Test gives a good "first cut" of the benefit or desirability of the program to customers. This information is especially useful for voluntary programs as an indication of potential participation rates.

For programs that involve a utility incentive, the Participant Test can be used for program design considerations such as the minimum incentive level, whether incentives are really needed to induce participation, and whether changes in incentive levels will induce the desired amount of participation.

These test results can be useful for program penetration analyses and developing program participation goals, which will minimize adverse ratepayer impacts and maximize benefits.

For fuel substitution programs, the Participant Test can be used to determine whether program participation (i.e. choosing one fuel over another) will be in the long-run best interest of the customer. The primary means of establishing such assurances is the net present value, which looks at the costs and benefits of the fuel choice over the life of the equipment.

2 It should be noted that if a demand-side program is beneficial to its participants (NPVp > 0 and BCRp > 1.0) using a particular discount rate, the program has an internal rate of return (IRR) of at least the value of the discount rate.

Weaknesses of the Participant Test None of the Participant Test results (discounted payback, net present value, or benefit-cost ratio) accurately capture the complexities and diversity of customer decision-making processes for demand-side management investments. Until or unless more is known about customer attitudes and behavior, interpretations of Participant Test results continue to require considerable judgment. Participant Test results play only a supportive role in any assessment of conservation and load management programs as alternatives to supply projects.

Formulae The following are the formulas for discounted payback, the net present value (NPVp) and the benefit-cost ratio (BCRp) for the Participant Test.

NPV P = Bp - Cp NPVavp = (Bp - Cp) / P BCRp = Bp / Cp DPp = Min j such that Bj > Cj

Where:

NPVp = Net present value to all participants NPVavp = Net present value to the average participant BCRp = Benefit-cost ratio to participants DPp = Discounted payback in years Bp = NPV of benefit to participants Cp = NPV of costs to participants Bj = Cumulative benefits to participants in year j Cj = Cumulative costs to participants in year j P = Number of program participants J = First year in which cumulative benefits are cumulative costs. d = Interest rate (discount)

The Benefit (Bp) and Cost (Cp) terms are further defined as follows:

!

" + ++

N t t ttt d INCTCBR BP 1 1 )1( + !

" + + N t t atat d PAAB 1 1 )1(

!

" + +

N t t tt d BIPC C 1 1 )1(

Where:

BRt = Bill reductions in year t Bit = Bill increases in year t

11 TCt = Tax credits in year t INCt = Incentives paid to the participant by the sponsoring utility in year t 3

PCt = Participant costs in year t to include: • Initial capital costs, including sales tax 4

• Ongoing operation and maintenance costs include fuel cost • Removal costs, less salvage value • Value of the customer's time in arranging for installation, if significant PACat = Participant avoided costs in year t for alternate fuel devices (costs of devices not chosen) Abat = Avoided bill from alternate fuel in year t

The first summation in the Bp equation should be used for conservation and load management programs. For fuel substitution programs, both the first and second summations should be used for Bp.

Note that in most cases, the customer bill impact terms (BRt, BIt, and AB at ) are further determined by costing period to reflect load impacts and/or rate schedules, which vary substantially by time of day and season. The formulas for these variables are as follows:

!!

+""#+""#= I i I i tititititititt OBRKDACDGKEACEGBR 11 ):():(

AB at = (Use BRt formula, but with rates and costing periods appropriate for the alternate fuel utility)

!!

+"##$+"##$= I i I i tititititititt OBIKDACDGKEACEGBI 11 ))1(:())1(:(

Where: ΔEG it = Reduction in gross energy use in costing period i in year t ΔDG it = Reduction in gross billing demand in costing period i in year t AC:E it = Rate charged for energy in costing period i in year t

3 Some difference of opinion exists as to what should be called an incentive. The term can be interpreted broadly to include almost anything. Direct rebates, interest payment subsidies, and even energy audits can be called incentives. Operationally, it is necessary to restrict the term to include only dollar benefits such as rebates or rate incentives (monthly bill credits). Information and services such as audits are not considered incentives for the purposes of these tests. If the incentive is to offset a specific participant cost, as in a rebate-type incentive, the full customer cost (before the rebate must be included in the PC t term

4 If money is borrowed by the customer to cover this cost, it may not be necessary to calculate the annual mortgage and discount this amount if the present worth of the mortgage payments equals the initial cost. This occurs when the discount rate used is equal to the interest rate of the mortgage. If the two rates differ (e.g., a loan offered by the utility), then the stream of mortgage payments should be discounted by the discount rate chosen.

12 AC:D it = Rate charged for demand in costing period i in year t K it = 1 when ΔEGit or ΔDGit is positive (a reduction) in costing period i in year t, and zero otherwise OBR t = Other bill reductions or avoided bill payments (e.g.,, customer charges, standby rates). OBI t = Other bill increases (i.e. customer charges, standby rates). I = Number of periods of participant’s participation

In load management programs such as TOU rates and air-conditioning cycling, there are often no direct customer hardware costs. However, attempts should be made to quantify indirect costs customers may incur that enable them to take advantage of TOU rates and similar programs.

If no customer hardware costs are expected or estimates of indirect costs and value of service are unavailable, it may not be possible to calculate the benefit-cost ratio and discounted payback period.

13 Chapter 3 The Ratepayer Impact Measure Test 5

Definition The Ratepayer Impact Measure (RIM) test measures what happens to customer bills or rates due to changes in utility revenues and operating costs caused by the program. Rates will go down if the change in revenues from the program is greater than the change in utility costs. Conversely, rates or bills will go up if revenues collected after program implementation are less than the total costs incurred by the utility in implementing the program. This test indicates the direction and magnitude of the expected change in customer bills or rate levels.

Benefits and Costs The benefits calculated in the RIM test are the savings from avoided supply costs. These avoided costs include the reduction in transmission, distribution, generation, and capacity costs for periods when load has been reduced and the increase in revenues for any periods in which load has been increased. The avoided supply costs are a reduction in total costs or revenue requirements and are included for both fuels for a fuel substitution program. The increase in revenues are also included for both fuels for fuel substitution programs. Both the reductions in supply costs and the revenue increases should be calculated using net energy savings.

The costs for this test are the program costs incurred by the utility, and/or other entities incurring costs and creating or administering the program, the incentives paid to the participant, decreased revenues for any periods in which load has been decreased and increased supply costs for any periods when load has been increased. The utility program costs include initial and annual costs, such as the cost of equipment, operation and maintenance, installation, program administration, and customer dropout and removal of equipment (less salvage value). The decreases in revenues and the increases in the supply costs should be calculated for both fuels for fuel substitution programs using net savings.

How the Results can be Expressed The results of this test can be presented in several forms: the lifecycle revenue impact (cents or dollars) per kWh, kW, therm, or customer; annual or first-year revenue impacts (cents or dollars per kWh, kW, therms, or customer); benefit-cost ratio; and net present value. The primary units of measurement are the lifecycle revenue impact, expressed as the change in rates (cents per kWh for electric energy, dollars per kW for electric capacity, cents per therm for natural gas) and the net present value. Secondary test results are the lifecycle revenue

5 The Ratepayer Impact Measure Test has previously been described under what was called the "Non-Participant Test." The Non-Participant Test has also been called the "Impact on Rate Levels Test."

14 impact per customer, first-year and annual revenue impacts, and the benefit-cost ratio. LRI RIM values for programs affecting electricity and gas should be calculated for each fuel individually (cents per kWh or dollars per kW and cents per therm) and on a combined gas and electric basis (cents per customer).

The lifecycle revenue impact (LRI) is the one-time change in rates or the bill change over the life of the program needed to bring total revenues in line with revenue requirements over the life of the program. The rate increase or decrease is expected to be put into effect in the first year of the program. Any successive rate changes such as for cost escalation are made from there. The first-year revenue impact (FRI) is the change in rates in the first year of the program or the bill change needed to get total revenues to match revenue requirements only for that year. The annual revenue impact (ARI) is the series of differences between revenues and revenue requirements in each year of the program. This series shows the cumulative rate change or bill change in a year needed to match revenues to revenue requirements. Thus, the ARIRIM for year six per kWh is the estimate of the difference between present rates and the rate that would be in effect in year six due to the program. For results expressed as lifecycle, annual, or first-year revenue impacts, negative results indicate favorable effects on the bills of ratepayers or reductions in rates. Positive test result values indicate adverse bill impacts or rate increases.

Net present value (NPV RIM ) gives the discounted dollar net benefit of the program from the perspective of rate levels or bills over some specified time period. A net present value above zero indicates that the program will benefit (lower) rates and bills.

The benefit-cost ratio (BCR RIM) is the ratio of the total benefits of a program to the total costs discounted over some specified time period. A benefit-cost ratio above one indicates that the program will lower rates and bills.

Strengths of the Ratepayer Impact Measure (RIM) Test In contrast to most supply options, demand-side management programs cause a direct shift in revenues. Under many conditions, revenues lost from DSM programs have to be made up by ratepayers. The RIM test is the only test that reflects this revenue shift along with the other costs and benefits associated with the program.

An additional strength of the RIM test is that the test can be used for all demand-side management programs (conservation, load management, fuel substitution, and load building). This makes the RIM test particularly useful for comparing impacts among demand-side management options.

Some of the units of measurement for the RIM test are of greater value than others, depending upon the purpose or type of evaluation. The lifecycle revenue impact per customer is the most useful unit of measurement when comparing the merits of programs with highly variable scopes (e.g.,, funding levels) and when analyzing a wide range of programs that

15 include both electric and natural gas impacts. Benefit-cost ratios can also be very useful for program design evaluations to identify the most attractive programs or program elements.

If comparisons are being made between a program or group of conservation/load management programs and a specific resource project, lifecycle cost per unit of energy and annual and first-year net costs per unit of energy are the most useful way to express test results. Of course, this requires developing lifecycle, annual, and first-year revenue impact estimates for the supply-side project.

Weaknesses of the Ratepayer Impact Measure (RIM) Test Results of the RIM test are probably less certain than those of other tests because the test is sensitive to the differences between long-term projections of marginal costs and long-term projections of rates, two cost streams that are difficult to quantify with certainty.

RIM test results are also sensitive to assumptions regarding the financing of program costs. Sensitivity analyses and interactive analyses that capture feedback effects between system changes, rate design options, and alternative means of financing generation and non- generation options can help overcome these limitations. However, these types of analyses may be difficult to implement.

An additional caution must be exercised in using the RIM test to evaluate a fuel substitution program with multiple end use efficiency options. For example, under conditions where marginal costs are less than average costs, a program that promotes an inefficient appliance may give a more favorable test result than a program that promotes an efficient appliance. Though the results of the RIM test accurately reflect rate impacts, the implications for long- term conservation efforts need to be considered.

Formulae: The formulae for the lifecycle revenue impact (LRI RIM)' net present value (NPV RIM), benefit-cost ratio (BCR RIM)' the first-year revenue impacts and annual revenue impacts are presented below:

LRIRIM = (CRIM - BRIM) / E FRIRIM = (CRIM - BRIM) / E for t = I ARIRIMt = FRIRIM for t = I = (CRIMt - BRIMt )/Et for t=2, .............., N NPVRIM = BRIM-CRIM

BCRRIM` = BRIM/CRIM where:

LRIRIM = Lifecycle revenue impact of the program per unit of energy (kWh or therm) or demand (kW) (the one-time change in rates) or per customer (the change in customer bills over the life of the program). (Note: An appropriate choice of kWh, therm, kW, and customer should be made)

FRIRIM = First-year revenue impact of the program per unit of energy, demand, or per customer.

ARIRIM = Stream of cumulative annual revenue impacts of the program per unit of energy, demand, or per customer. (Note: The terms in the ARI formula are not discounted; thus they are the nominal cumulative revenue impacts. Discounted cumulative revenue impacts may be calculated and submitted if they are indicated as such. Note also that the sum of the discounted stream of cumulative revenue impacts does not equal the LRI RIM')

NPVRIM = Net present value levels

BCRRIM = Benefit-cost ratio for rate levels

BRIM = Benefits to rate levels or customer bills CRIM = Costs to rate levels or customer bills E = Discounted stream of system energy sales (kWh or therms) or demand sales (kW) or first-year customers. (See Appendix D for a description of the derivation and use of this term in the LRIRIM test.)

The B RIM and C RIM terms are further defined as follows:

!!

"

" + + + + N t t at N t t t RIM d UAC d RGUAC B t 1 1 1 1 )1()1(

!!

"

" + + + +++ N t t at N t t tttt RIM d RL d INCPRCRLUIC C 1 1 1 1 )1()1(

!

" +

N t t t d E E 1 1 )1(

Where: UACt = Utility avoided supply costs in year t UICt = Utility increased supply costs in year t RGt = Revenue gain from increased sales in year t RLt = Revenue loss from reduced sales in year t PRCt = Program Administrator program costs in year t Et = System sales in kWh, kW or therms in year t or first year customers UACat = Utility avoided supply costs for the alternate fuel in year t Rlat = Revenue loss from avoided bill payments for alternate fuel in year t (i.e., device not chosen in a fuel substitution program)

17 For fuel substitution programs, the first term in the B RIM and C RIM equations represents the sponsoring utility (electric or gas), and the second term represents the alternate utility. The RIM test should be calculated separately for electric and gas and combined electric and gas.

The utility avoided cost terms (UAC t , UIC t , and UAC at ) are further determined by costing period to reflect time-variant costs of supply:

):():( 11 ititit I i I i itititt KDMCDNKEMCENUCA!!"+!!"=

UAC at = (Use UACt formula, but with marginal costs and costing periods appropriate for the alternate fuel utility.)

!!

"##$+"##$ I i I i itititititt KDMCDNKEMCENUIC 11 ))1(:())1(:(

Where:

[Only terms not previously defined are included here.] ΔENit = Reduction in net energy use in costing period i in year t ΔDNit = Reduction in net demand in costing period i in year t MC:Eit = Marginal cost of energy in costing period i in year t MC:Dit = Marginal cost of demand in costing period i in year t

The revenue impact terms (RG t , RL t , and RL at ) are parallel to the bill impact terms in the Participant Test. The terms are calculated exactly the same way with the exception that the net impacts are used rather than gross impacts. If a net-to-gross ratio is used to differentiate gross savings from net savings, the revenue terms and the participant's bill terms will be related as follows:

RGt = BIt * (net-to-gross ratio) RLt = BRt * (net-to-gross ratio) Rlat = Abat * (net-to-gross ratio)

18 Chapter 4 Total Resource Cost Test 6

Definition The Total Resource Cost Test measures the net costs of a demand-side management program as a resource option based on the total costs of the program, including both the participants' and the utility's costs.

The test is applicable to conservation, load management, and fuel substitution programs. For fuel substitution programs, the test measures the net effect of the impacts from the fuel not chosen versus the impacts from the fuel that is chosen as a result of the program. TRC test results for fuel substitution programs should be viewed as a measure of the economic efficiency implications of the total energy supply system (gas and electric).

A variant on the TRC test is the Societal Test. The Societal Test differs from the TRC test in that it includes the effects of externalities (e.g.,, environmental, national security), excludes tax credit benefits, and uses a different (societal) discount rate.

Benefits and Costs: This test represents the combination of the effects of a program on both the customers participating and those not participating in a program. In a sense, it is the summation of the benefit and cost terms in the Participant and the Ratepayer Impact Measure tests, where the revenue (bill) change and the incentive terms intuitively cancel (except for the differences in net and gross savings).

The benefits calculated in the Total Resource Cost Test are the avoided supply costs, the reduction in transmission, distribution, generation, and capacity costs valued at marginal cost for the periods when there is a load reduction. The avoided supply costs should be calculated using net program savings, savings net of changes in energy use that would have happened in the absence of the program. For fuel substitution programs, benefits include the avoided device costs and avoided supply costs for the energy, using equipment not chosen by the program participant.

The costs in this test are the program costs paid by both the utility and the participants plus the increase in supply costs for the periods in which load is increased. Thus all equipment costs, installation, operation and maintenance, cost of removal (less salvage value), and administration costs, no matter who pays for them, are included in this test. Any tax credits are considered a reduction to costs in this test. For fuel substitution programs, the costs also include the increase in supply costs for the utility providing the fuel that is chosen as a result of the program.

6 This test was previously called the All Ratepayers Test

19 How the Results Can be Expressed The results of the Total Resource Cost Test can be expressed in several forms: as a net present value, a benefit-cost ratio, or as a levelized cost. The net present value is the primary unit of measurement for this test. Secondary means of expressing TRC test results are a benefit-cost ratio and levelized costs. The Societal Test expressed in terms of net present value, a benefit-cost ratio, or levelized costs is also considered a secondary means of expressing results. Levelized costs as a unit of measurement are inapplicable for fuel substitution programs, since these programs represent the net change of alternative fuels which are measured in different physical units (e.g.,, kWh or therms). Levelized costs are also not applicable for load building programs.

Net present value (NPVTRC) is the discounted value of the net benefits to this test over a specified period of time. NPVTRC is a measure of the change in the total resource costs due to the program. A net present value above zero indicates that the program is a less expensive resource than the supply option upon which the marginal costs are based.

The benefit-cost ratio (BCRTRC) is the ratio of the discounted total benefits of the program to the discounted total costs over some specified time period. It gives an indication of the rate of return of this program to the utility and its ratepayers. A benefit-cost ratio above one indicates that the program is beneficial to the utility and its ratepayers on a total resource cost basis.

The levelized cost is a measure of the total costs of the program in a form that is sometimes used to estimate costs of utility-owned supply additions. It presents the total costs of the program to the utility and its ratepayers on a per kilowatt, per kilowatt hour, or per therm basis levelized over the life of the program.

The Societal Test is structurally similar to the Total Resource Cost Test. It goes beyond the TRC test in that it attempts to quantify the change in the total resource costs to society as a whole rather than to only the service territory (the utility and its ratepayers). In taking society's perspective, the Societal Test utilizes essentially the same input variables as the TRC Test, but they are defined with a broader societal point of view. More specifically, the Societal Test differs from the TRC Test in at least one of five ways. First, the Societal Test may use higher marginal costs than the TRC test if a utility faces marginal costs that are lower than other utilities in the state or than its out-of-state suppliers. Marginal costs used in the Societal Test would reflect the cost to society of the more expensive alternative resources. Second, tax credits are treated as a transfer payment in the Societal Test, and thus are left out. Third, in the case of capital expenditures, interest payments are considered a transfer payment since society actually expends the resources in the first year. Therefore, capital costs enter the calculations in the year in which they occur. Fourth, a societal discount rate should be used 7. Finally, Marginal costs used in the Societal Test would also contain externality costs of power generation not captured by the market system. An illustrative and

7 Many economists have pointed out that use of a market discount rate in social cost-benefit analysis undervalues the interests of future generations. Yet if a market discount rate is not used, comparisons with alternative investments are difficult to make .

20 by no means exhaustive list of ‘externalities and their components’ is given below (Refer to the Limitations section for elaboration.) These values are also referred to as ‘adders’ designed to capture or internalize such externalities. The list of potential adders would include for example:

The benefit of avoided environmental damage: The CPUC policy specifies two ‘adders’ to internalize environmental externalities, one for electricity use and one for natural gas use. Both are statewide average values. These adders are intended to help distinguish between cost-effective and non cost-effective energy-efficiency programs. They apply to an average supply mix and would not be useful in distinguishing among competing supply options. The CPUC electricity environmental adder is intended to account for the environmental damage from air pollutant emissions from power plants. The CPUC- adopted adder is intended to cover the human and material damage from sulfur oxides (SOX), nitrogen oxides (NOX), volatile organic compounds (VOC, sometimes called reactive organic gases or ROG), particulate matter at or below 10 micron diameter (PM10), and carbon. The adder for natural gas is intended to account for air pollutant emissions from the direct combustion of the gas. In the CPUC policy guidance, the adders are included in the tabulation of the benefits of energy efficiency programs. They represent reduced environmental damage from displaced electricity generation and avoided gas combustion. The environmental damage is the result of the net change in pollutant emissions in the air basins, or regions, in which there is an impact. This change is the result of direct changes in powerplant or natural gas combustion emission resulting from the efficiency measures, and changes in emissions from other sources, that result from those direct changes in emissions.
The benefit of avoided transmission and distribution costs – energy efficiency measures that reduce the growth in peak demand would decrease the required rate of expansion to the transmission and distribution network, eliminating costs of constructing and maintaining new or upgraded lines.
The benefit of avoided generation costs – energy efficiency measures reduce consumption and hence avoid the need for generation. This would include avoided energy costs, capacity costs and T&D line
The benefit of increased system reliability: The reductions in demand and peak loads

from customers opting for self generation, provide reliability benefits to the distribution

system in the forms of:
1. Avoided costs of supply disruptions
2. Benefits to the economy of damage and control costs avoided by customers and
industries in the digital economy that need greater than 99.9 level of reliable

electricity service from the central grid

c. Marginally decreased System Operator’s costs to maintain a percentage reserve of

electricity supply above the instantaneous demand

d. Benefits to customers and the public of avoiding blackouts.

21 5. Non-energy benefits: Non-energy benefits might include a range of program-specific benefits such as saved water in energy-efficient washing machines or self generation units, reduced waste streams from an energy-efficient industrial process, etc.

Non-energy benefits for low income programs: The low income programs are social programs which have a separate list of benefits included in what is known as the ‘low income public purpose test’. This test and the sepcific benefits associated with this test are outside the scope of this manual.
Benefits of fuel diversity include considerations of the risks of supply disruption, the effects of price volatility, and the avoided costs of risk exposure and risk management.

Strengths of the Total Resource Cost Test The primary strength of the Total Resource Cost (TRC) test is its scope. The test includes total costs (participant plus program administrator) and also has the potential for capturing total benefits (avoided supply costs plus, in the case of the societal test variation, externalities). To the extent supply-side project evaluations also include total costs of generation and/or transmission, the TRC test provides a useful basis for comparing demand- and supply-side options.

Since this test treats incentives paid to participants and revenue shifts as transfer payments (from all ratepayers to participants through increased revenue requirements), the test results are unaffected by the uncertainties of projected average rates, thus reducing the uncertainty of the test results. Average rates and assumptions associated with how other options are financed (analogous to the issue of incentives for DSM programs) are also excluded from most supply-side cost determinations, again making the TRC test useful for comparing demand-side and supply-side options.

Weakness of the Total Resource Cost Test The treatment of revenue shifts and incentive payments as transfer payments, identified previously as a strength, can also be considered a weakness of the TRC test. While it is true that most supply-side cost analyses do not include such financial issues, it can be argued that DSM programs should include these effects since, in contrast to most supply options, DSM programs do result in lost revenues.

In addition, the costs of the DSM "resource" in the TRC test are based on the total costs of the program, including costs incurred by the participant. Supply-side resource options are typically based only on the costs incurred by the power suppliers.

Finally, the TRC test cannot be applied meaningfully to load building programs, thereby limiting the ability to use this test to compare the full range of demand-side management options.

Formulas

22 The formulas for the net present value (NPV TRC )' the benefit-cost ratio (BCR TRC and levelized costs are presented below:

NPVTRC = BTRC - CTRC BCRTRC = BTRC /CTRC LCTRC = LCRC / IMP

Where: NPVTRC = Net present value of total costs of the resource BCRTRC = Benefit-cost ratio of total costs of the resource LCTRC = Levelized cost per unit of the total cost of the resource (cents per kWh for conservation programs; dollars per kW for load management programs) BTRC = Benefits of the program CTRC = Costs of the program LCRC = Total resource costs used for levelizing IMP = Total discounted load impacts of the program PCN = Net Participant Costs

The B TRC C TRC LCRC, and IMP terms are further defined as follows:

!!

"" + + + + +

N t N t t atat t tt d PACUAC d TCUAC BTRC 11 11 )1()1(

!

" + ++

N t t ttt d UICPCNPRC CTRC 1 1 )1(

!

" + "+

N t t ttt d TCPCNPRC LCRC 1 1 )1(

1 11 )1( ) ( )( !

$ % & ' =((= )) t n t n i itit d periodpeakIwhereDNorENIMP

[All terms have been defined in previous chapters.]

The first summation in the BTRC equation should be used for conservation and load management programs. For fuel substitution programs, both the first and second summations should be used.

23 Chapter 5 Program Administrator Cost Test Definition The Program Administrator Cost Test measures the net costs of a demand-side management program as a resource option based on the costs incurred by the program administrator (including incentive costs) and excluding any net costs incurred by the participant. The benefits are similar to the TRC benefits. Costs are defined more narrowly.

Benefits and Costs The benefits for the Program Administrator Cost Test are the avoided supply costs of energy and demand, the reduction in transmission, distribution, generation, and capacity valued at marginal costs for the periods when there is a load reduction. The avoided supply costs should be calculated using net program savings, savings net of changes in energy use that would have happened in the absence of the program. For fuel substitution programs, benefits include the avoided supply costs for the energy-using equipment not chosen by the program participant only in the case of a combination utility where the utility provides both fuels.

The costs for the Program Administrator Cost Test are the program costs incurred by the administrator, the incentives paid to the customers, and the increased supply costs for the periods in which load is increased. Administrator program costs include initial and annual costs, such as the cost of utility equipment, operation and maintenance, installation, program administration, and customer dropout and removal of equipment (less salvage value). For fuel substitution programs, costs include the increased supply costs for the energy-using equipment chosen by the program participant only in the case of a combination utility, as above.

In this test, revenue shifts are viewed as a transfer payment between participants and all ratepayers. Though a shift in revenue affects rates, it does not affect revenue requirements, which are defined as the difference between the net marginal energy and capacity costs avoided and program costs. Thus, if NPVpa > 0 and NPVRIM < 0, the administrator’s overall total costs will decrease, although rates may increase because the sales base over which revenue requirements are spread has decreased.

How the Results Can be Expressed The results of this test can be expressed either as a net present value, benefit-cost ratio, or levelized costs. The net present value is the primary test, and the benefit-cost ratio and levelized cost are the secondary tests.

24 Net present value (NPVpa) is the benefit of the program minus the administrator's costs, discounted over some specified period of time. A net present value above zero indicates that this demand-side program would decrease costs to the administrator and the utility.

The benefit-cost ratio (BCRpa) is the ratio of the total discounted benefits of a program to the total discounted costs for a specified time period. A benefit-cost ratio above one indicates that the program would benefit the combined administrator and utility's total cost situation.

The levelized cost is a measure of the costs of the program to the administrator in a form that is sometimes used to estimate costs of utility-owned supply additions. It presents the costs of the program to the administrator and the utility on per kilowatt, per kilowatt-hour, or per therm basis levelized over the life of the program.

Strengths of the Program Administrator Cost Test As with the Total Resource Cost test, the Program Administrator Cost test treats revenue shifts as transfer payments, meaning that test results are not complicated by the uncertainties associated with long-term rate projections and associated rate design assumptions. In contrast to the Total Resource Cost test, the Program Administrator Test includes only the portion of the participant's equipment costs that is paid for by the administrator in the form of an incentive. Therefore, for purposes of comparison, costs in the Program Administrator Cost Test are defined similarly to those supply-side projects which also do not include direct customer costs.

Weaknesses of the Program Administrator Cost Test By defining device costs exclusively in terms of costs incurred by the administrator, the Program Administrator Cost test results reflect only a portion of the full costs of the resource.

The Program Administrator Cost Test shares two limitations noted previously for the Total Resource Cost test: (1) by treating revenue shifts as transfer payments, the rate impacts are not captured, and (2) the test cannot be used to evaluate load building programs.

Formulas The formulas for the net present value, the benefit-cost ratio and levelized cost are presented below:

NPVpa = Bpa - Cpa BCRpa = Bpa/Cpa LCpa = LCpa/IMP

Where: NPVpa Net present value of Program Administrator costs BCRpa Benefit-cost ratio of Program Administrator costs

25 LCpa Levelized cost per unit of Program Administrator cost of the resource Bpa Benefits of the program Cpa Costs of the program LCpc Total Program Administrator costs used for levelizing

!! + "

" + + +

N t t at N t t t pa d UAC d UAC B 1 1 1 1 )1()1(

!

" + ++

N t t ttt pa d UICINCPRC C 1 1 )1(

!

" + +

N t t tt d INCPRC LCpc 1 1 )1(

[All variables are defined in previous chapters.]

The first summation in the Bpa equation should be used for conservation and load management programs. For fuel substitution programs, both the first and second summations should be used.

26 Appendix A

Inputs to Equations and Documentation A comprehensive review of procedures and sources for developing inputs is beyond the scope of this manual. It would also be inappropriate to attempt a complete standardization of techniques and procedures for developing inputs for such parameters as load impacts, marginal costs, or average rates. Nevertheless, a series of guidelines can help to establish acceptable procedures and improve the chances of obtaining reasonable levels of consistent and meaningful cost-effectiveness results. The following "rules" should be viewed as appropriate guidelines for developing the primary inputs for the cost-effectiveness equations contained in this manual:

In the past, Marginal costs for electricity were based on production cost model simulations that clearly identify key assumptions and characteristics of the existing generation system as well as the timing and nature of any generation additions and/or power purchase agreements in the future. With a deregulated market for wholesale electricity, marginal costs for electric generation energy should be based on forecast market prices, which are derived from recent transactions in California energy markets. Such transactions could include spot market purchases as well as longer term bilateral contracts and the marginal costs should be estimated based on components for energy as well as demand and/or capacity costs as is typical for these contracts.
In the case of submittals in conjunction with a utility rate proceeding, average rates used in DSM program cost-effectiveness evaluations should be based on proposed rates. Otherwise, average rates should be based on current rate schedules. Evaluations based on alternative rate designs are encouraged.
Time-differentiated inputs for electric marginal energy and capacity costs, average energy rates, and demand charges, and electric load impacts should be used for (a) load management programs, (b) any conservation program that involves a financial incentive to the customer, and (c) any Fuel Substitution or Load Building program. Costing periods used should include, at a minimum, summer and winter, on-, and off-peak; further disaggregation is encouraged.
When program participation includes customers with different rate schedules, the average rate inputs should represent an average weighted by the estimated mix of participation or impacts. For General Rate Case proceedings it is likely that each major rate class within each program will be considered as program elements requiring separate cost- effectiveness analyses for each measure and each rate class within each program.

27 5. Program administration cost estimates used in program cost-effectiveness analyses should exclude costs associated with the measurement and evaluation of program impacts unless the costs are a necessary component to administer the program.

For DSM programs or program elements that reduce electricity and natural gas consumption, costs and benefits from both fuels should be included.
The development and treatment of load impact estimates should distinguish between gross (i.e., impacts expected from the installation of a particular device, measure, appliance) and net (impacts adjusted to account for what would have happened anyway, and therefore not attributable to the program). Load impacts for the Participants test should be based on gross, whereas for all other tests the use of net is appropriate. Gross and net program impact considerations should be applied to all types of demand-side management programs, although in some instances there may be no difference between gross and net.
The use of sensitivity analysis, i.e. the calculation of cost-effectiveness test results using alternative input assumptions, is encouraged, particularly for the following programs: new programs, programs for which authorization to substantially change direction is being sought (e.g.,, termination, significant expansion), major programs which show marginal cost-effectiveness and/or particular sensitivity to highly uncertain input(s).

The use of many of these guidelines is illustrated with examples of program cost effectiveness contained in Appendix B.

28 Appendix B Summary of Equations and Glossary of Symbols Basic Equations Participant Test NPVP = BP - CP NPVavp = (BP - CP) / P BCRP = BP/CP DPP = min j such that Bj > Cj

Ratepayer Impact Measure Test LRIRIM = (CRIM - BRIM) / E FRIRIM = (CRIM - BRIM) / E for t = 1 ARIRIMt = FRIRIM for t = 1 = (CRIMt- BRIMt )/Et for t=2,... ,N NPVRIM = BRIM — CRIM BCRRIM = BRIM /CRIM

Total Resource Cost Test

NPVTRC = BTRC - CTRC BCRTRC = BTRC / CTRC LCTRC = LCRC / IMP

Program Administrator Cost Test

NPVpa = Bpa - Cpa BCRpa = Bpa / Cpa LCpa = LCpa / IMP

Benefits and Costs Participant Test

!!

"" + + + + ++

N t N t t atat t ttt d PACAB d INCTCBR Bp 11 11 )1()1(

!

" + + N t t tt d BIPC Cp 1 1 )1(

Ratepayer Impact Measure Test

!!

"" + + + +

N t N t t at t tt RIM d UAC d RGUAC B 11 11 )1()1(

!!

"

" + + + +++

N t t at N t t tttt RIM d RL d INCPRCRLUIC C 1 1 1 1 )1()1(

!

" +

N t t t d E E 1 1 )1(

Total Resource Cost Test

!!

"" + + + + +

N t N t t atat t tt TRC d PACUAC d TCUAC B 11 11 )1()1(

!

" + ++

N t t ttt TRC d UICPCNPRC C 1 1 )1(

!

" + "+

N t t ttt TRC d TCPCNPRC L 1 1 )1(

1 11 )1( ) ( )( !

$ % & ' =((= )) t n t n i itit d periodpeakIwhereDNorENIMP

Program Administrator Cost Test

!!

"" + + +

N t N t t at t t pa d UAC d UAC B 11 11

)1(

!

" + ++

N t t ttt pa d UICINCPRC C 1 1 )1(

!

" + +

N t t tt d INCPRC LCPA 1 1 )1(

Glossary of Symbols Abat = Avoided bill reductions on bill from alternate fuel in year t AC:Dit = Rate charged for demand in costing period i in year t AC:Eit = Rate charged for energy in costing period i in year t ARIRIM = Stream of cumulative annual revenue impacts of the program per unit of energy, demand, or per customer. Note that the terms in the ARI formula are not discounted, thus they are the nominal cumulative revenue impacts. Discounted cumulative revenue impacts may be calculated and submitted if they are indicated as such. Note also that the sum of the discounted stream of cumulative revenue impacts does not equal the LRIRIM* BCRp = Benefit-cost ratio to participants BCRRIM = Benefit-cost ratio for rate levels BCRTRC = Benefit-cost ratio of total costs of the resource BCRpa = Benefit-cost ratio of program administrator and utility costs BIt = Bill increases in year t Bj = Cumulative benefits to participants in year j Bp = Benefit to participants BRIM = Benefits to rate levels or customer bills BRt = Bill reductions in year t BTRC = Benefits of the program Bpa = Benefits of the program Cj = Cumulative costs to participants in year i

31 Cp = Costs to participants CRIM = Costs to rate levels or customer bills CTRC = Costs of the program Cpa = Costs of the program D = discount rate ΔDgit = Reduction in gross billing demand in costing period i in year t ΔDnit = Reduction in net demand in costing period i in year t DPp = Discounted payback in years E = Discounted stream of system energy sales-(kWh or therms) or demand sales (kW) or first-year customers ΔEgit = Reduction in gross energy use in costing period i in year t ΔEnit = Reduction in net energy use in costing period i in year t Et = System sales in kWh, kW or therms in year t or first year customers FRIRIM = First-year revenue impact of the program per unit of energy, demand, or per customer. IMP = Total discounted load impacts of the program INCt = Incentives paid to the participant by the sponsoring utility in year t First year in which cumulative benefits are > cumulative costs. Kit = 1 when ΔEGit or ΔDGit is positive (a reduction) in costing period i in year t, and zero otherwise LCRC = Total resource costs used for levelizing LCTRC = Levelized cost per unit of the total cost of the resource LCPA = Total Program Administrator costs used for levelizing Lcpa = Levelized cost per unit of program administrator cost of the resource LRIRIM = Lifecycle revenue impact of the program per unit of energy (kWh or therm) or demand (kW)-the one-time change in rates-or per customer-the change in customer bills over the life of the program. MC:Dit = Marginal cost of demand in costing period i in year t MC:Eit = Marginal cost of energy in costing period i in year t NPVavp = Net present value to the average participant NPVP = Net present value to all participants NPVRIM = Net present value levels NPVTRC = Net present value of total costs of the resource NPVpa = Net present value of program administrator costs OBIt = Other bill increases (i.e., customer charges, standby rates) OBRt = Other bill reductions or avoided bill payments (e.g., customer charges, standby rates). P = Number of program participants PACat = Participant avoided costs in year t for alternate fuel devices

32 PCt = Participant costs in year t to include: • Initial capital costs, including sales tax • Ongoing operation and maintenance costs • Removal costs, less salvage value • Value of the customer's time in arranging for installation, if significant PRCt = Program Administrator program costs in year t PCN = Net Participant Costs RGt = Revenue gain from increased sales in year t RLat = Revenue loss from avoided bill payments for alternate fuel in year t (i.e., device not chosen in a fuel substitution program) RLt = Revenue loss from reduced sales in year t TCt = Tax credits in year t UACat = Utility avoided supply costs for the alternate fuel in year t UACt = Utility avoided supply costs in year t PAt = Program Administrator costs in year t UICt = Utility increased supply costs in year t

33 Appendix C.

Derivation of Rim Lifecycle Revenue Impact Formula Most of the formulas in the manual are either self-explanatory or are explained in the text. This appendix provides additional explanation for a few specific areas where the algebra was considered to be too cumbersome to include in the text.

Rate Impact Measure The Ratepayer Impact Measure lifecycle revenue impact test (LRIRIM) is assumed to be the one-time increase or decrease in rates that will re-equate the present valued stream of revenues and stream of revenue requirements over the life of the program.

Rates are designed to equate long-term revenues with long-term costs or revenue requirements. The implementation of a demand-side program can disrupt this equality by changing one of the assumptions upon which it is based: the sales forecast. Demand-side programs by definition change sales. This expected difference between the long-term revenues and revenue requirements is calculated in the NPVRIM The amount which present valued revenues are below present valued revenue requirements equals NPVRIM

The LRIRIM is the change in rates that creates a change in the revenue stream that, when present valued, equals the NPVRIM* If the utility raises (or lowers) its rates in the base year by the amount of the LRIRIM' revenues over the term of the program will again equal revenue requirements. (The other assumed changes in rates, implied in the escalation of the rate values, are considered to remain in effect.)

Thus, the formula for the LRIRIM is derived from the following equality where the present value change in revenues due to the rate increase or decrease is set equal to the NPVRIM or the revenue change caused by the program.

!

" +

=" N t t tRIM RIM d ELRI NPV 1 1 )1(

Since the LRI RIM term does not have a time subscript, it can be removed from the summation, and the formula is then:

!

" + #=" N t t t RIMRIM d E LRINPV 1 1 )1(

34 Rearranging terms, we then get:

!

" + "= N t t t RIMRIM d E NPVLRI 1 1 )1(

Thus,

!

" +

N t t t d E E 1 1 )1(

23 CAR Part 460 — Promotional Practices of Electric and Gas Public Utilities

Chapter XVI

Subchapter A

Subpart 1

23 CAR § 460-101 Declaration of public policy {#sec-23-car-460-101 omnilex-key=us-ar-regs-official--title-23-part-460--23 CAR § 460-101}

23 CAR § 460-102 Definitions {#sec-23-car-460-102 omnilex-key=us-ar-regs-official--title-23-part-460--23 CAR § 460-102}

23 CAR § 460-103 Prohibition of promotional practices {#sec-23-car-460-103 omnilex-key=us-ar-regs-official--title-23-part-460--23 CAR § 460-103}

23 CAR § 460-104 Standards governing promotional practices {#sec-23-car-460-104 omnilex-key=us-ar-regs-official--title-23-part-460--23 CAR § 460-104}

23 CAR § 460-105 Filing of proposed promotional practices {#sec-23-car-460-105 omnilex-key=us-ar-regs-official--title-23-part-460--23 CAR § 460-105}

23 CAR § 460-106 Approval by the Arkansas Public Service Commission {#sec-23-car-460-106 omnilex-key=us-ar-regs-official--title-23-part-460--23 CAR § 460-106}

23 CAR § 460-107 Notices {#sec-23-car-460-107 omnilex-key=us-ar-regs-official--title-23-part-460--23 CAR § 460-107}

23 CAR § 460-108 Biennial report {#sec-23-car-460-108 omnilex-key=us-ar-regs-official--title-23-part-460--23 CAR § 460-108}

23 CAR § 460-109 Transition period {#sec-23-car-460-109 omnilex-key=us-ar-regs-official--title-23-part-460--23 CAR § 460-109}

23 CAR pt. 460, Appendix A California Standard Practice Manual - Economic Analysis of Demand-Side Programs and Projects {#sec-23-car-pt.-460-appendix-a omnilex-key=us-ar-regs-official--title-23-part-460--23 CAR pt. 460, Appendix A}

!

" + ++

N t t ttt d INCTCBR BP 1 1 )1( + !

!

" + +

!!

!!

!!

"

!!

"

!

" +

!!

!!

"" + + + + +

!

" + ++

!

" + "+

1 11 )1( ) ( )( !

!! + "

" + + +

!

" + ++

!

" + +

!!

"" + + + + ++

!

!!

"" + + + +

!!

"

" + + + +++

!

" +

!!

"" + + + + +

!

" + ++

!

" + "+

1 11 )1( ) ( )( !

!!

"" + + +

!

" + ++

!

" + +

!

!

!

!

" +

Continue your research in ChatGPT or Claude